With stick of french chalk included.

Read more less

Square Sticks - 10 x 100mm For general layout marking in a wide variety of applications from marking tailor's seams and weld marking on sheet materials in fabrication industries.

Read more less

Sticky Circles for reliable mic placement. In this pack you get 90 pre-cut 24mm diameter Sticky Circles. URSA Sticky Circles are 24mm in diameter, see-through and very low profile at just 0.4mm. The sticky tape is certified hypoallergenic so it can be used directly on skin. You can also use it on fabrics as it leaves no residue and peels off without tearing. Each URSA Sticky Circle has been pre-cut and has a small peel-off tab for easy & fast use. They are compatible with a variety of mic mounts including RM11s, DPA Concealers and can also be used with URSA MiniMounts. You get 30 of these stickies with every pack of URSA Plush, Fur or SoftCircles. More About URSA Sticky Circles URSA Sticky Circles (Pack of 90) Each 24mm diameter URSA Sticky Circle has been pre-cut and has a small peel-off tab for easy & fast use. They are compatible with a variety of mic mounts including RM11s, DPA Concealers and can also be used with URSA MiniMounts. (You get 30 of these stickies with every pack of URSA Plush, Fur or Soft Circles.)

Read more less

Ventilated Tool Belt. Allow your waist to breathe with Dirty Rigger multi-layered material construction. The padded 3D internally-breathable mesh provides excellent ventilation throughout the belt, minimising uncomfortable under-belt sweat. Tried and tested heavy duty 50mm belt buckle helps to keep the Tool Belt comfortably secured around your waist and can be removed single handily when required. Fully compatible with the Dirty Rigger pouch and accessories range. Internally-breathable mesh for ventilation Quick release buckle 5cm (2in) belt Compatible with Dirty Rigger accessories Adjust to fits sizes 30in-42in

Read more less

It's all about the base. An abrasion and puncture-resistant 4mm rubber base helps prevent pointed tools from piercing through the bottom of the pouch. Keep your equipment organised with a 2.5ltr master pocket and 5 slip-in pockets positioned around the inner walls. Instantly access your most commonly used tools from four open-topped pockets on the bag s outer edges and a built in pass-through for a long handle screwdriver** gives even more versatility. 2.5ltr main storage pocket 17cm(W) x 8cm(D) x 19cm(H)* 5 slip-in inner pockets various sizes 2 instant access outer pockets (sides) 7cm(W) x 2.5cm(D) x 13.5cm(H)* 2 instant access outer pockets (front) 7cm(W) x 2.5cm(D) x 10cm(H)* Screwdriver pass-through** 4 steel d-rings for additional attachments Side mounted grab handle 50mm belt loop Rugged 600 600 denier nylon construction Overall dimensions 23cm(W) x 12cm(D) x 20cm(H) Pouch contents not included. Measurements are approximate *Pockets may be more narrow at the base. **Tool must be sufficiently wide inside of the pass-through in order for it to be retained in the pocket. Tools must be individually inspected to ensure they are held securely in place.

Read more less

Useful for quickly covering small cameras or lenses to protect them from water or dust. Sold individually.

Read more less

Grips can use this to lubricate track. Or you can use it to lubricate a bunch of other stuff. Also useful for cleaning and removing sticky residue. Features: Gets under dirt, marks and grease, making it easy to wipe them away Protects metal surfaces with corrosion-resistant ingredients Loosens rust-to-metal bonds and frees stuck, frozen or rusted metal parts It quickly dries out electrical systems to eliminate moisture-induced short circuits Smart Straw: This option has a permanently attached spray mechanism, it offers a quick and simple action for precision and wide area spray.

Read more less

Made from high tensile steel with a self colour finish, meaning these are uncoated. Angular lifts will significantly lower working load limits and should be avoided. Hardened/Tempered. Thread length approx 20mm. When using these for some applications such as on camera top handles, the thread may need cut down. This will jepordise the integrity of the eyebolt and to what they are rated to. Therefor we sell them in their original condition.

Read more less

True 75 Ω design meets the stringent HDTV / DVD requirements “rearTWIST Principle” locking/unlocking Excellent cable protection and retention Guarantees a lifetime of min. 1000 mating cycles Precise Swiss machined brass parts for outstanding durability Fully compatible with conventional BNC chassis connectors

Read more less

Dulling spray is a fine, colourless spray used to reduce glare on reflective surfaces and minimize hot spots. Naturally an opposite to white! Reduces flare on shiny black foregrounds. Simple effects obtained on small backgrounds, used alone or with matt white. All K-Line sprays are easily removed with a soft cloth or with a little light spirit. None are intended to be permanent - they are rapid aids with a maximum of safety. 400ml - Made in Britain.

Read more less

These Hook & Loop cable ties are great for managing all times of electronic wires, cords, and cables. The ability to quickly fasten and release the ties make them a useful addition to your kit. For a more secure hold, thread one end through the eye hole to form a wrap. This design allows cables to be connected together, making the strap longer. Features: Strong adherence Can be cut to length Reusable and durable design  Nylon material provides long life span and weather resistance   Size: 10mm x 150mm Pack of 10 cable ties

Read more less

Constructed of padded, hook and loop knit with a non-scratch nylon backing, these squares can be wrapped around lenses, tools, or anything else that will fit inside. Hook and loop tabs on all four corners let you wrap and stick them in any shape. Features: 19 inch from corner to corner Hook and loop for sealing off the corners Ideal for colour co-ordinating Non scratch nylon backing Available in Black, Blue, Red, Yellow & Grey These are available in three sizes: 11", 15" and 19"

Read more less

Upright Holder for Clapperboards and Smartphones Presentation Clapperboard and Slate Stand, with insert groove for smartphones and tablets. Wooden Block with two insert grooves, 3.2mm and 12mm, to allow the Slate and Smartphone/Tablet to stand on a table or flat surface Wooden Presentation Stand with Filmsticks Logo on the Smartphone/Tablet side Flippable to allow for mounting a smartphone or tablet for viewing on a flat surface Allows the user to engrave or fix a plaque on the Stand Slate side for a presentation gift Neutral wood colour to suit most shelves and tables Weight and Dimensions: L 80mm (3.15") x H 70mm (2.76") x D 20mm (0.79") 66g (2.33 oz) net weight *Clapperboard and accessories not included. This is for the stand only.

Read more less

These versatile belts are 5cm wide by 115cm long and can be cut down with scissors to suit small waists. They have been designed for use with our range of URSA Belt Pouches which come in four sizes (mini, small, medium & large) to suit all TX units. URSA Belts come in 2 Colours: Beige or Black. Machine Washable at 40 degrees, tumble dry at a low heat. They can also be used with AquaPacs or as a strap to clip transmitters onto. We developed a special double bonded fabric specifically for these belts which is gives them more strength, return and adds a little thickness. This helps keep the belts from stringing up under the weight of transmitters. They could be particularly useful for theatre and live performance where artists often have to rig two transmitters onto one belt. URSA Belts Demo URSA Straps use certified OEKO-TEX hypoallergenic fabric and gripper.

Read more less

Filter Tabs are perfect for attaching to the side of your camera for quick and easy identification of what filter is currently fitted. Our filter tabs are made in house out of a acrylic laminate material to ensure they are robust and can endure life on set. The assistant set comes with a range of Filter Tabs that covers the most common filters. From this you can supplement with additional sets or individual tabs. This Set comes with: 2x blank (Opaque clapperboard material so you can write your own filter on it) OP FLAT POLA TRUE POLA ND 0.3 ND 0.6 ND 0.9 ND 1.2 IRND 0.3 IRND 0.6 IRND 0.9 IRND 1.2 IRND 1.5 IRND 1.8 IRND 2.1 S/E 0.3 S/E 0.6 S/E 0.9 S/E 1.2 H/E 0.3 H/E 0.6 H/E 0.9 H/E 1.2 +1/2 DIO +1 DIO +2 DIO +3 DIO *The set also comes with a 2x blank Tabs made out of white acrylic that you can write on. This is perfect for when you have another random filter you need to identify. Supplied with Hook material (Velcro) pre applied to the rear so they are ready to go. This is a build to order item - Please allow a working day for them to be produced. Individual Tabs or custom sets are also available, please contact us. Available in the following Colours: Black/White White/Black Red/White Blue/White White/Red White/Blue Yellow/Black If you require another colour please contact us.

Read more less

Simply use this marker just like a pen to marker on any surface. Plastic, foil, rubber, wood and even glass are no match for this pack of black Sharpie permanent markers. The high intensity pigment of the innot only dries instantly but is also both waterproof and smear-proof.

Read more less

Ash Blonde – light brown, slightly golden sandy colour. Medium density and dries fast. When washed, leaves yellow/green stains on fabric. Very popular colour. Try using with Dark and Mid brown for a shading effect. Start with Dark Brown and shade into Ash Blonde. Ash Blonde ageing spray is a fine mist semi-transparent spray dye that makes things look dirty and old, or aged. Dirty red/brown colour. A lighter shade of brown than Dark Brown. The spray is water soluble and can be smeared and reworked by wetting with water. Fast drying. Ozone friendly. Usage Instructions: Ensure surfaces are dry and grease free. Mask areas not to be sprayed. Shake can before use. Use sparingly, apply several fine coats rather than one heavy coat. The shade will darken with each coat applied. Hold can upright 30cm (12 inches) away from the surface, and spray across the surface in one smooth sweep, keeping the nozzle fully depressed. Spots of concentrated dye may appear if the button is only partially depressed. For small patches, spray through holes cut in a piece of paper. For dark patches, spray closer to the surface. Heavy spraying may drip or puddle. Smear the spray by re-wetting with water, and then dabbing or rubbing with a damp or wet cloth. With some fabrics it’s easier to smear by wetting the sprayed fabric and then rubbing the wet area together between your hands. Smearing is easier when the spray is still wet, but is also possible after the spray has fully dried. It may not be possible to smear spray applied to absorbent surfaces. May not adhere to some polished surfaces. Our ageing sprays are water soluble and the effects of spraying will be lost by washing in water, but there may still be staining. Do not use outside in wet weather. Ageing spray may cause permanent staining. Test before use on off-cuts or hidden surfaces, and then wash to check for any staining.

Read more less

Soot Black ageing spray has a stronger, more powerful spray nozzle than our other ageing sprays. The spray deposits a semi-opaque layer of black dye that creates a dirty, black old or aged look. The spray is water soluble and can be smeared and reworked by wetting with water, but much less water soluble than our other ageing sprays. Fast drying. Ozone friendly. Soot Black – a rich matt black.  Very high density, very dark, almost opaque.  A very resistant and permanent colour, no matter what the fabric.  Even visible on darker coloured items.  Least washable of all our sprays, will almost always leave a black stain.  More powerful than the other ageing sprays and takes longer to dry. Usage Instructions: The spray comes out at a faster speed than other ageing sprays – it’s best to test before use. Ensure surfaces are dry and grease free. Mask areas not to be sprayed. Shake can before use. Use sparingly, apply several fine coats rather than one heavy coat. The shade will darken with each coat applied. Hold can upright 30cm (12 inches) away from the surface, and spray across the surface in one smooth sweep, keeping the nozzle fully depressed. Spots of concentrated dye may appear if the button is only partially depressed. For small patches, spray through holes cut in a piece of paper. For dark patches, spray closer to the surface. Heavy spraying may drip or puddle. Smear the spray by re-wetting with water, and then dabbing or rubbing with a damp or wet cloth. With some fabrics it’s easier to smear by wetting the sprayed fabric and then rubbing the wet area together between your hands. Smearing is easier when the spray is still wet, but is also possible after the spray has fully dried. It may not be possible to smear spray applied to absorbent surfaces. May not adhere to some polished surfaces. Our ageing sprays are water soluble and the effects of spraying will be lost by washing in water, but there may still be staining. Do not use outside in wet weather.

Read more less

• Black underside with black adhesive• Matt black low-reflective top surface• Individually wrapped rolls• Minimal light penetration• Easy tear by hand High Performance Black AdhesiveWith an all-black underside and adhesive, this tape is very discrete when applied to most black fabrics, blackout materials, black stage sets and props. Anti-Reflection CoatingA satin-matt, low reflection surface. Ideal for use in professional TV, film & theatre. Durable 80 Mesh ConstructionA durable 80 mesh construction offers good levels of durability.

Read more less

MOUNTING A LavALIER MICROPHONE IN CLOTHING OR COSTUMES AND ON THE BODY HAS JUST BECOME MUCH EASIER. The Lav Concealer is a soft pliable mount that covers many different mounting options, moulding itself to the surface it is attached to. Because of it's rubber material, it also acts as a shock mount, protecting the mic capsule from vibration and absorbing friction noise to give you clearer sound recordings. These innovative lav mounts fit the capsule perfectly and, along with making hiding the mic easier, protects it from a build up of glue which can result from repeatedly attaching tape directly to the mic. The Lav Concealers can be attached directly to skin or clothing using our Lav Concealer Tape. The tape is very strong, hypoallergenic and easy to apply, for mounting on fabric or skin without worry. It also includes a newly designed metal clothing clip and fabric guards, which can be applied in any configuration you like, depending on the mounting style. It can also be sewn into costumes by the costume department for daily repeated use. Compatible with Sanken Cos-11 lavalier microphone. Lav CONCEALER FEATURES CREATES SPACE:Keeps material away from the microphone capsule in tight spaces under or in clothing, protecting the mic from friction noise and vibrations; making your recordings sound cleaner. SHOCK ABSORBING:The moulded rubber concealer is made for excellent vibration and friction absorption, while the metal clothing clip and fabric guards prevent the transmission of vibration through the concealer to the microphone capsule. COLOUR OPTIONS:Available in Matte Black or Matte White finish. The matte finish is non-reflective for discrete hiding. WIRE FABRIC GUARDS:The removable wire fabric guard keeps fabric from touching the microphone capsule. The combination of wire and rubber materials acts as excellent friction absorption, cutting transmission of friction to the mic capsule. EXTREME FABRIC GUARD:Also included is the new Extreme Fabric Guard; it moves the point of contact between the fabric and the guard, to a more central position over the body of the Lav Concealer . This can be used where the subject is wearing clothing which is made from a particularly coarse or noisy material. Both fabric guards can be used together, in lieu of the clothing clip, if the situation calls for it. CLIP, TAPE OR SEWING MOUNTING OPTIONS:Provides many options for mounting lavalier mics on talent easily, effectively and quickly, many times under high pressure on sets. ENVIRONMENTALLY SOUND:The Lav Concealer is made from 100% natural rubber, which is biodegradable and kind to the environment. The black and white versions don't use any harmful chemical compounds to achieve the colouring. The natural rubber used in manufacturing The Lav Concealer is biodegradable, which the environment will thank you for. In terms of clarity, using a soft, pliable rubber means it absorbs more vibrations than harder materials (eg. plastic), preventing unnecessary noise from ever reaching the microphone capsule. The Lav Concealer includes two fabric guards and a clothing clip, made of sprung metal. These attach to the concealer in tiny holes on the front and back. Having two different materials operating in unison helps prevent friction or vibrations from being transferred from one to the other, and eventually to the capsule. It moulds to your mounting style: Both the clothing clip and fabric guards are removable, and you can mount them on the front, back, top-side or bottom-side of The Lav Concealer. For the ultimate fabric guard configuration, use tape to attach the concealer and mount the Extreme fabric guard on the top-side of the Lav Concealer, with the regular fabric guard on the bottom, to lift the fabric off the entire concealer. WHAT’S INCLUDED: 1x Rubber Lav Concealer (Black/White) 1x Metal Clothing Clip (Black/Silver) 1x Wire Fabric Guard (Black/Silver) 1x Wire Fabric Guard Extreme (Black/Silver) (Specific Models) 6x Lav Concealer Tape

Read more less

Low profile plastic hook on one side and velour loop on the other. Perfect for cable & cord management. Cut To Required Length On Site Low Profile Hook & Loop Fasteners Easy, adjustable and re-usable.

Read more less

The URSA MiniMount Stickies are perfect for use with their URSA MiniMounts. They are hypoallergenic and safe to use against skin and also do not leave residue if used on costumes and delicate fabrics.

Read more less

YOUR LAVALIER MIC'S BEST FRIEND ON WINDY DAYS The Bubblebee Windbubble consists of an outer shell of the finest imitation fur (we do like them animals) and an inner core of nothing. And this 'nothing' is exactly what makes the bubble so special. The air enters the bubble for a short visit, finds it rather dull, and quickly leaves again without harming the microphone inside. So instead of the wind hammering on the microphone and making those horrible, “I’m in the middle of a hurricane,” sounds, the capsule is kept in a calm space and allowed to perform at its best. Each package contains two identical Windbubbles. WINDBUBBLE FEATURES: WORLD-RENOWNED PROTECTION FROM WINDBest in the industry wind protection thanks to the bubble-effect in the design. The construction of the Windbubble holds a quiet space around the mic capsule, allowing it to perform its duties in the best way possible and delivering detailed and natural sound to your transmitter or recorder. WINDBUBBLES WON'T FALL OFFThey are built to stay safe and secure on your Lavalier microphone, with a tight fitting opening aperture - hence the four available sizes.  CHOOSE YOUR SIZEAvailable in four different sizes for over 50 popular lavalier mics. Please consult our Size Guide to check this. CHOOSE YOUR COLOURAvailable in six different colours of high quality Bubblebee fur to make it easier to find a Windbubble for every occasion. NATURAL SOUNDOur fur and mesh construction makes The Windbubble acoustically transparent to keep the sound very close to the microphones natural frequency response. MULTI-PILE FURThe short, dense hair of the fur gives the Windbubble a rounded and organic shape while the longer fur slows wind down gradually for quieter wind protection. NATURAL COLOURSThe Bubblebee fur is less shiny to blend better with skin, clothes and other surrounding materials. QUALITY YOU CAN TRUSTDesigned in Denmark by sound lovers, for sound lovers! MOUNT THE WINDBUBBLE WITH CONFIDENCE The Windbubbles are specially constructed to be mounted quickly and easily on your specified type of microphones and to not fall off during use. To this end, the fit can be fairly tight around the base of the capsule. The tiny elastic wire legs make it easy to mount the Windbubbles on the Lavalier microphone, by locating the hole easily. If the lav capsule is on the larger side, you can practise mounting the Windbubble on the tapered end of a ball-point pen as this helps get a feel for it. It is important that you check the correct size(s) suitable for your lavalier microphone. Please consult our Size Guide to check this. Size 1 - Built for microphones with a diameter of 3,0-4,0 mmElastic opening circumference: 28 mm (1.10”)For Example:Sanken COS-11 (without metal windscreen)Countryman B6, B2D, E6Sennheiser MKE 1Sony ECM-90DPA 6060 Size 2 - Built for microphones with a diameter of 5,0-8,0 mm:Elastic opening circumference: 35 mm (1.38”)For Example:Sanken COS-11 (without metal windscreen)Countryman B3DPA 4060Sennheiser MKE 2, ME2, ME2-US (without windscreen), ME2-IILOM Mikro Uši Size 3 - Built for microphones with a diameter of 5,0-9,0 mm:Elastic opening circumference: 40 mm (1.57”)For Example:Sanken COS-11 (with metal windscreen)Countryman EMWDPA 4060 (with metal windscreen)Sennheiser MKE 2 (with MZW 2 windshield), ME2, ME2-US (with windscreen), ME2-II Size 4 - Built for microphones with a diameter of 8,0-13,0 mm:Elastic opening circumference: 42 mm (1.65”)For Example:Sanken COS-11 (with large metal windscreen)Countryman EMWDPA 4060 (with metal windscreen)Sennheiser: ME 4, ME 102 & ME 104 (with metal MZW 2 windshield)LOM Uši Pro

Read more less

PEC PADs are the ideal photo wipes for those who hate photo wipes! Until PEC PADs came along, photo wipes fell apart, left lint and scratched emulsions. PEC PADs are extremely strong, lint-free and so soft and pure (99.999%) it is almost impossible to scratch an emulsion with them. PEC PADs are so soft they can be safely used to clean all types of sensitive surfaces: scanners, CD's, mirrors, lenses, telescopes etc. When PEC PADs are used with PEC-12, they are ideally suited for cleaning photographic film and print emulsions. Used with Eclipse Lens cleaner they are excellent for cleaning all types of coated and uncoated lenses. The 10cm x10cm (4 x 4 inch) wipes are perfect for cleaning 35mm and other small areas. PEC PAD is not recommended for cleaning the CCD.

Read more less