A utility-grade polycoated cloth duct tape with an aggressive natural rubber adhesive, ideally suited for packaging, wrapping and sealing, binding and bundling, and general maintenance. 50mm Wide x 50m Long

Read more less

The Windbubble PRO microphone windshields will give you the ultimate wind protection you can get for you omni-directional lavalier, field recording or headset mic. Whatever the make or size of your mic, the Windbubble PRO range of premium quality furry windshields keeps away those horrible wind noises and allows the clean and clear frequencies in. The Windbubble PRO lav mic windshield consists of a soft rubber mount. Unlike hard plastic mounts this special rubber mount absorbs shocks and stops vibrations transferring to your mic’s capsule. The rubber mount holds the furry windshield firmly in place on your mic, making sure it doesn't slip off. In addition to this, the rubber mount has a slight conical shape inside, which ensures you can't push your microphone too far into the windshield. This is very important to ensure that your microphone has a "bubble" of dead-air around the capsule for optimal wind protection and audio clarity. This means that your mic will consistently stay in the best possible position for maximum efficiency. The fixed positioning of the mic using the rubber mount has given us the ability to engineer a smaller overall profile for the Windbubble PRO without compromising on the efficacy of the wind protection. However, each mount size is also available in a larger 'Extreme' version which consists of an inner foam core, surrounded by our much-loved multi-pile faux fur, to offer you an even greater level of wind protection for your microphone. These are especially helpful on those super windy exteriors and a perfect solution for factual, ENG and broadcast shoots. Every Windbubble PRO is available in our renowned multi-pile faux fur. This unique fur has been specially designed with varying lengths of fur to help gradually slow down the wind particles before reaching the mic. The base of the fur has a higher density of shorter hairs and an acoustically transparent backing material for maximum frequency transparency. So instead of the wind hammering on the microphone and making those horrible, “I’m in the middle of a hurricane,” sounds, the capsule is kept in a calm bubble of wind protection and allowed to perform at its best. The Windbubble PRO is also available in XS, Small and Medium, in a single or twin-pack of lapel mic windshields and in four different colours (black, grey, white, and beige) to allow you to colour-match to the costume or outfit of the talent. Please note: The Windbubble PRO is only suitable for omnidirectional microphones. If you have a directional microphone, then the original Windbubble is the best microphone windshield for your mic. WINDBUBBLE PRO FEATURES: WORLD-RENOWNED PROTECTION FROM WINDBest in the industry wind protection thanks to the bubble-effect and rubber mount in the design. The construction of the Windbubble PRO holds a quiet space of dead-air around the mic capsule, allowing it to perform the best way possible and delivering detailed and naturally transparent audio to your transmitter or recorder. WINDBUBBLE PROS WON'T FALL OFFThe rubber mount firmly grips your mic, ensuring the windshield will stay in place and you don't have to worry about it falling off mid-shoot. CHOOSE YOUR MODELThe Windbubble PROs are available in a standard version, 'Extreme' version for greater wind protection or 'Extreme' Long-Haired for those super windy conditions.  NATURAL SOUNDThe fur and mesh construction makes The Windbubble PRO acoustically transparent to keep the sound very close to the microphone’s natural frequency response. MULTI-PILE FURThe short, dense hair of the fur gives the Windbubble PRO a rounded and organic shape while the longer fur slows wind down gradually for best-in-class wind protection. The Bubblebee fur is less shiny than others, to better blend with skin, clothes and other surrounding materials. QUALITY YOU CAN TRUSTDesigned in Denmark by sound lovers, for sound lovers! It is important that you check the correct size(s) Windbubble PRO windshield suitable for your omnidirectional lavalier microphone. Please consult the size guide below to check this. Large - Built for omni microphones with a diameter of 11.5-14.0mmFor Example: LOM Uši, Uši ProMicBooster Clippy EM272 ITEM CODES:BBI-WP2-L-BKBBI-WP2-L-BK-EBBI-WP2-L-BK-EL

Read more less

The original Sprig for 3/8" Whitworth threaded holes. Made from a flexible material and features a flexible thread for fast installation with a secure hold. A perfect accessory for securing and cleaning up the cables on your camera or monitors. Cable management device for filmmakers! Includes: 3 Sprigs

Read more less

The original Sprig for 1/4" Whitworth threaded holes. Made from a flexible material and features a flexible thread for fast installation with a secure hold. A perfect accessory for securing and cleaning up the cables on your camera or monitors. Cable management device for filmmakers! Includes: 6 Sprigs Also Available is the Sprig Holder (sold separately). Perfect for helping keep your Sprigs organised and safe.

Read more less

Constructed of padded, hook and loop knit with a non-scratch nylon backing, these squares can be wrapped around lenses, tools, or anything else that will fit inside. Hook and loop tabs on all four corners let you wrap and stick them in any shape. Features: 19 inch from corner to corner Hook and loop for sealing off the corners Ideal for colour co-ordinating Non scratch nylon backing Available in Black, Blue, Red, Yellow & Grey These are available in three sizes: 11", 15" and 19"

Read more less

Constructed of padded, hook and loop knit with a non-scratch nylon backing, these squares can be wrapped around lenses, tools, or anything else that will fit inside. Hook and loop tabs on all four corners let you wrap and stick them in any shape. Features: 19 inch from corner to corner Hook and loop for sealing off the corners Ideal for colour co-ordinating Non scratch nylon backing Available in Black, Blue, Red, Yellow & Grey These are available in three sizes: 11", 15" and 19"

Read more less

Constructed of padded, hook and loop knit with a non-scratch nylon backing, these squares can be wrapped around lenses, tools, or anything else that will fit inside. Hook and loop tabs on all four corners let you wrap and stick them in any shape. Features: 19 inch from corner to corner Hook and loop for sealing off the corners Ideal for colour co-ordinating Non scratch nylon backing Available in Black, Blue, Red, Yellow & Grey These are available in three sizes: 11", 15" and 19"

Read more less

Useful for attaching smaller pieces of kit to the side of cameras or the backs of monitors etc. The revolutionary 3M Dual Lock Re-closable Fastening System is changing the way people think about hook and loop systems. Being up to 12 times stronger than regular hook and loop systems, these reliable self-adhesive strips are replacing unsightly mechanical fixings throughout transportation, business equipment, machinery, and signage and display markets. The mushroom shaped stems interlock and can be opened and closed hundreds of times with no seal degradation. What's more, as there's no drilling or locating necessary, assembly is quick and easy with Dual Lock. 25mm Wide. Benefits of 3M Dual Lock Fasteners include: Fast assembly with no drilling Invisible fixing High temperature and solvent resistance Can be die-cut to individual designs Acrylic versions for external use Re-sealable Up to 12 times stronger than normal systems Multiple profiles are available offering varying levels of interlocked strength aka; heavy duty velcro, dual lok, dual loc, SJ3550

Read more less

• Black underside with black adhesive• Matt black low-reflective top surface• Individually wrapped rolls• Minimal light penetration• Easy tear by hand High Performance Black AdhesiveWith an all-black underside and adhesive, this tape is very discrete when applied to most black fabrics, blackout materials, black stage sets and props. Anti-Reflection CoatingA satin-matt, low reflection surface. Ideal for use in professional TV, film & theatre. Durable 80 Mesh ConstructionA durable 80 mesh construction offers good levels of durability.

Read more less

This Edding 8280 UV Marker is ideal for labelling and creating hidden markings or secret messages on surfaces like wood, glass, metal and plastic, The ink can only be seen under UV light and is also waterproof and wear-resistant with a quick drying time. Securitas UV marker for hidden marking and labelling of almost all materials Permanent, quick-drying ink that only becomes clearly visible under UV light High-quality aluminium barrel The round nib has a stroke width of 1.5-3 mm Smudge-proof Waterproof Low odour

Read more less

Reduces a 3/8'' threaded screw to a standard 1/4'' Adapter from 3/8'' to 1/4'' screw Very small, and sturdy 2cm in height

Read more less

for light stands or tripods that have a top screw of 1/4'' Convert from female 1/4'' to 3/8'' male Made of Brass 2cm in height

Read more less

Dulling / Anti-Flare spray can be applied to mirrors or glass, metal, gloss paint and ceramics etc. Easy to remove; the water soluble spray can be wiped off non-porous surfaces by rubbing with a damp or wet cloth. It is both fast drying and ozone friendly. Tip: You can apply ageing spray over the top of dulling spray to create a matt finish ageing spray. Dulling / Anti-Flare spray looks like a fine layer of dirt on glass and can be smeared using a damp/wet cloth to create a patchy effect. Instructions for Use: The spray can must be at room temperature to work properly. For best results, store overnight at room temperature before use. Shake the spray can with the ball bearing rattling before every use. Use sparingly, apply several fine coats, not one heavy coat. Over application will reduce the dulling effect and may cause puddles. Best results are achieved when fine coats are applied. Ensure surfaces are dry & grease free. Mask areas not to be sprayed. Dulling spray may stain/damage some surfaces. Hold can upright 30cm (300mm) away from the surface, and spray across the surface in one smooth sweep, keeping the nozzle fully depressed. Spots of concentrated spray may appear if the button is only partially depressed. For small patches, spray through a hole cut in a piece of paper. Dulling spray is water soluble. The effects of spraying will be lost by washing in water. Do not use outside in wet weather. Practice your spraying technique on a disposable item before final use. Test before use on off-cuts or hidden surfaces/ off cuts for compatibility and adhesion. Available in 400ml sized spray.

Read more less

The Windbubble PRO microphone windshields will give you the ultimate wind protection you can get for you omni-directional lavalier, field recording or headset mic. Whatever the make or size of your mic, the Windbubble PRO range of premium quality furry windshields keeps away those horrible wind noises and allows the clean and clear frequencies in. The Windbubble PRO lav mic windshield consists of a soft rubber mount. Unlike hard plastic mounts this special rubber mount absorbs shocks and stops vibrations transferring to your mic’s capsule. The rubber mount holds the furry windshield firmly in place on your mic, making sure it doesn't slip off. In addition to this, the rubber mount has a slight conical shape inside, which ensures you can't push your microphone too far into the windshield. This is very important to ensure that your microphone has a "bubble" of dead-air around the capsule for optimal wind protection and audio clarity. This means that your mic will consistently stay in the best possible position for maximum efficiency. There are four sizes of rubber mounts available to fit the most commonly used omnidirectional lavalier mics, headset mics, or field recording stereo-pair microphones, this includes The Windbubble Pro (Twin pack) Large. The fixed positioning of the mic using the rubber mount has given us the ability to engineer a smaller overall profile for the Windbubble PRO without compromising on the efficacy of the wind protection. However, each mount size is also available in a larger 'Extreme' version which consists of an inner foam core, surrounded by our much-loved multi-pile faux fur, to offer you an even greater level of wind protection for your microphone. These are especially helpful on those super windy exteriors and a perfect solution for factual, ENG and broadcast shoots. Every Windbubble PRO is available in our renowned multi-pile faux fur. This unique fur has been specially designed with varying lengths of fur to help gradually slow down the wind particles before reaching the mic. The base of the fur has a higher density of shorter hairs and an acoustically transparent backing material for maximum frequency transparency. So instead of the wind hammering on the microphone and making those horrible, “I’m in the middle of a hurricane,” sounds, the capsule is kept in a calm bubble of wind protection and allowed to perform at its best. Each Windbubble PRO is available in a single or twin-pack of lapel mic windshields and in four different colours (black, grey, white, and beige) to allow you to colour-match to the costume or outfit of the talent. Please note: The Windbubble PRO is only suitable for omnidirectional microphones. If you have a directional microphone, then the original Windbubble is the best microphone windshield for your mic. WINDBUBBLE PRO FEATURES: WORLD-RENOWNED PROTECTION FROM WINDBest in the industry wind protection thanks to the bubble-effect and rubber mount in the design. The construction of the Windbubble PRO holds a quiet space of dead-air around the mic capsule, allowing it to perform the best way possible and delivering detailed and naturally transparent audio to your transmitter or recorder. WINDBUBBLE PROS WON'T FALL OFFThe rubber mount firmly grips your mic, ensuring the windshield will stay in place and you don't have to worry about it falling off mid-shoot. CHOOSE YOUR SIZE AND MODELThe Windbubble PROs are available in four different sizes to fit the most popular lavalier, head-worn or field recording mics. Each size is also available in a standard version or and 'Extreme' version for greater wind protection.  NATURAL SOUNDThe fur and mesh construction makes The Windbubble PRO acoustically transparent to keep the sound very close to the microphone’s natural frequency response. CHOOSE YOUR COLOURAvailable in four different colours (black, grey, white and beige) oh high quality Bubblebee faux fur to make it easier to match a Windbubble PRO colour to most outfits. MULTI-PILE FURThe short, dense hair of the fur gives the Windbubble PRO a rounded and organic shape while the longer fur slows wind down gradually for best-in-class wind protection. The Bubblebee fur is less shiny than others, to better blend with skin, clothes and other surrounding materials. QUALITY YOU CAN TRUSTDesigned in Denmark by sound lovers, for sound lovers! It is important that you check the correct size(s) Windbubble PRO windshield suitable for your omnidirectional lavalier microphone. Please consult the size guide below to check this. XS - Built for omni microphones with a diameter of 3.0-5.0mmFor Example: Countryman B3, B6, E6, H6Deity W.Lav Micro, W.Lav ProDPA 6060, 6061, 6066Sanken COS-11 (without metal popshield)Sennheiser HSP 2, MKE 1, MKE 2Sony ECM-88, ECM-90 Small - Built for omni microphones with a diameter of 5.0-6.5mm:For Example: Deity W.LavDPA 4060, 4061, 4062, 4063, 4066, 4071, 4166, 4266Røde Lavalier, Lavalier Go, SmartLav+ LINKLavSennheiser ME 2 (old style with removable popshield 5.8mm ø from G2/G3 series)Shure Duraplex DL4, DH5, Twinplex TL45, TL46, TL47, TL48Sony ECM-77 Medium - Built for omni microphones with a diameter of 6.0-8.0mm:For Example: LOM mikroUši, mikroUši ProSennheiser ME 2-US (old style with removable popshield 6.5mm ø from G3/G4 series)Sony ECM-V1Tascam TM-10LTentacle MIC-01 ITEM CODES:BBI-WP-XS-BK/WH/GY/BEBBI-WP-S-BK/WH/GY/BEBBI-WP-M-BK/WH/GY/BE BBI-WP-XS-BK/WH/GY/BE-EBBI-WP-S-BK/WH/GY/BE-EBBI-WP-M-BK/WH/GY/BE-E BBI-WP2-XS-BK/WH/GY/BEBBI-WP2-S-BK/WH/GY/BEBBI-WP2-M-BK/WH/GY/BE BBI-WP2-XS-BK/WH/GY/BE-EBBI-WP2-S-BK/WH/GY/BE-EBBI-WP2-M-BK/WH/GY/BE-E

Read more less

Engraved plastic plaque with 3M adhesive backing. Beveled edge.

Read more less

If you're looking for a superb solution for organising the most common household tasks, look no further! Whether you're planning to label folders, stickers on bottling jars or children's lunchboxes, the long-lasting, smudge-proof, wear-resistant edding 3000 permanent marker works on almost all materials. In addition, the round nib allows an even distribution of ink. You'll be impressed by the high-quality aluminium barrel and the long-lasting results in equal measure! This quick-drying, low-odour lightfast edding comes in a wide range of colours and works equally well on plastic, wood, metal, glass or cardboard. It's the perfect assistant for your everyday tasks, and fits as neatly in any kitchen, study or workshop as it does in your hand. Features: Durable and resistant to smudging and fading Bullet tip Tip Width: between 1.5 and 3mm Quick drying Odorless and lightfast Refillable Recommended use: marking and writing on almost any material (wood, leather, aluminium, metal, plastic, glass or cardboard).

Read more less

Keep germ free with these XXL+ Clothwipes that will fight and kill 99.99% of bacteria. Use these on your tools, in your vehicle, at work or home and on any surface that you need germ and dirt free. Due to the massive size and special absorbent capacity these wipes can move the toughest of grime and one wipe goes a lot further than you think… The beauty is in the cloth-like fabric that won’t rip or deteriorate during use. Plus, these wipes stay wetter and usable for longer than any other wipe, so you can go from one mess to the next with ease. Forget about costly cleansing solutions and wimpy paper towels and go for the wipes made to do it all. Suitable for use on all surfaces around the home, these wipes can be used for all sorts of dirt and grime cleaning. Features: 40 XXL+ Clothwipes – 38cm x 25cm. Double the Size of Common Wipes Dual action cleaner and sanitiser, with a Citrus Home Fresh scent Antibacterial – kills 99.99% of bacteria Sanitising efficacy exceeds EN1276 Stays wet and usable for over 60 minutes – most dry out in 5-10 minutes Don’t dry out when lid is left open for days – try it for a week! Flexible, recyclable packaging for less waste Hand safe & safe to use on all surfaces-kind to hands and surfaces Dispenses one wipe at a time Eliminates cross-contamination Large absorbency capacity

Read more less